5Th Gen Projectors *update 6/28/11* Actually doing it
#61
Posted 20 July 2011 - 08:36 PM
#62
Posted 23 July 2011 - 12:08 AM
zzapultimate, on 14 July 2011 - 11:20 AM, said:
Where did you tap into your parking lights at?
To be honest I pulled a bulb out and turned the parking lights on to see which filament is the one that stays on always, I then just pulled the bulb out and you can see the leads that the filement go to into the socket and just tapped that wire.
There's one ground and two 12v wires on is obviously the continuous and the other the signal portion. If you get the wrong one just use the other.
#63
Posted 23 July 2011 - 12:14 AM
Chris7130, on 20 July 2011 - 02:59 AM, said:
I did that for awhile too but then just disabled the drl/auto light feature all together. Id rather control them manually with the switch. Its not good for them if you forget and start the car at night with the e-brake off they come on then shut off when you hit the starter then come back on.
Trust me it really does shorten the life of the bulbs or it will mess the ballast up it's self. Been there done that multiple times on different cars or seen friends do it and say it will be fine. Then wonder why one of there lights burned out 4 months in and I have had the same set for 2 years.
#64
Posted 23 July 2011 - 12:19 AM
zzapultimate, on 20 July 2011 - 09:36 PM, said:
Do it get the flicker harness for around ten bucks on ebay, trigger the relay with the parking light 12v and trigger your high beam shields or w/e they are called in the HID projectors with the 12v from the high beam socket or sockets how ever that has to be done.
Then get another harness and some fog light with matching hids and trigger those with the parking lights too for some added brightness. Plus then you have everything on at once.
It makes a huge difference to have them all on at once trust me haha.
#65
Posted 18 August 2011 - 09:50 PM
In other news.. the projectors are AMAZING!
This post has been edited by zzapultimate: 18 August 2011 - 09:53 PM
#66
Posted 20 August 2011 - 09:03 AM
#67
Posted 20 August 2011 - 02:21 PM

'96 Monte L67 - Ported heads | Full 3" Exhaust | Ported TB | 180* T-stat | 104's | HAI | UDAP | SSPlog&Ported Rear | P&P Gen III | Walbro | AFC |
'93 Prelude H22A1 - Header | CAI | 2.5" SS Exhaust |
http://usatyourservice.webs.com | http://www.expertpcnc.com
#68
Posted 23 August 2011 - 12:03 AM

1997 Monte Carlo LS: Refurbished 3100 V6 Engine & Transmission, New Fuel Pump, New Gas Cap (haha), Chrome Grille, Clear Chrome/Chrystal Headlights,Clear Side Markers All The Way Around, Dual Flip Out Touch Screen Stereo, 2-2007 S15L7 Kicker Solo Baric Square Subwoofers with Yellow Top Optima Battery And 2500 Watt Kicker Solo Baric 2005 Amp And Stinger Wiring Kit With Capacitor, MMS PCM Tune, Retractable Atenna, Low Profile Wind Deflectors.
#69
Posted 16 November 2011 - 10:58 AM
Im serious if its a decent price on the labor and all I will prolly be sending you a set. I hit a deer on the pass side and need a new headlight anyway and I'm tired of the crap light output of our headlights.
PM me if happen to see this
This post has been edited by famousmonte98: 16 November 2011 - 10:59 AM
#70
Posted 16 November 2011 - 05:53 PM
famousmonte98, on 16 November 2011 - 09:58 AM, said:
Im serious if its a decent price on the labor and all I will prolly be sending you a set. I hit a deer on the pass side and need a new headlight anyway and I'm tired of the crap light output of our headlights.
PM me if happen to see this
I would consider it. The projectors themselves are $120. add another $35ish for HID kit (or $70 if you want HID highs like I do aslo). A few other supplies might bring you to $200. A wiring harness too? That's probably $75ish in supplies the way i have it set up with 4 relays, wire, connectors, and wire loom. I have no clue how long it would take me to make them in hours, but I imagine quite a few especially with all the adjusting and aiming too. These are pretty rough estimates though.
We are looking at $275 headlights WITHOUT labor. How much are you willing to spend?
#71
Posted 19 November 2011 - 09:50 AM
So the cost would be 120 for the projectors plus whatever you feel your time is worth.
This post has been edited by famousmonte98: 19 November 2011 - 09:50 AM
#72
Posted 20 November 2011 - 10:04 PM
famousmonte98, on 19 November 2011 - 08:50 AM, said:
So the cost would be 120 for the projectors plus whatever you feel your time is worth.
P.M.'d
This post has been edited by zzapultimate: 20 November 2011 - 10:04 PM
#73
Posted 22 November 2011 - 09:41 AM
low beam output and high beam output, like how they look on a road?
#75
Posted 28 January 2012 - 03:19 AM

96 Z34 3.4 SC DOHC Getrag, 284 5sd manual transmission, stage 3spec clutch, 97 engine 1 of 1 Roots SC LQ1 in the world 8.5 psi.
#76
Posted 29 January 2012 - 11:28 AM
Dave96Z34, on 28 January 2012 - 02:19 AM, said:
No, but it looks similar. Those are definitely a knock-off.
#77
Posted 31 January 2012 - 05:03 PM
Dave96Z34, on 28 January 2012 - 04:19 AM, said:
You should buy these or these if you want projectors for the low.
PS3 Gamertag: BiggLDogg add me if you have a PS3

Help



















